Research Article
Surface Modification of Ti-6Al-4V Alloy by Composite Coating of Polycaprolactone Nanofibers-Fluoroapatite Nanoparticles Doped with Silicon and Magnesium
Issue:
Volume 8, Issue 2, December 2024
Pages:
22-29
Received:
22 July 2024
Accepted:
24 August 2024
Published:
11 September 2024
Abstract: The purpose of this research was to create polycaprolactone nanocomposite coating - fluor apatite nanoparticles doped with silicon and magnesium, as well as polycaprolactone coating on the alloy in order to improve and modify the biological properties of this alloy. For this purpose, nano composite coating and polycaprolactone coating were first created by immersion methode. Then the physical, corrosion and biological properties of the coating created by different methods were investigated. The results indicated the creation of a uniform nanocomposite coating with a thickness of about 6.26 micrometers, with appropriate structure and phases, and an increase in roughness by adding nanoparticles to the polycaprolactone coating. Electrochemical measurements Ti6Al4V showed that the sample coated with polycaprolactone with nanoparticles has polarization RP=5.349×105 Ωcm2 resistance, which is higher than the sample coated with caprolactone with polarization resistance RP=1.191×105 Ωcm2 and the sample without coating with polarization resistance RP=5.2453×104 Ωcm2. Cytotoxicity test showed the non-cytotoxicity of the coatings. Also, the cell growth and proliferation of the sample with nano composite coating compared to the sample without coating has a statistically significant difference. Cell adhesion on the sample with nanocomposite coating was also much better than the sample without coating and the sample with polycaprolactone coating.
Abstract: The purpose of this research was to create polycaprolactone nanocomposite coating - fluor apatite nanoparticles doped with silicon and magnesium, as well as polycaprolactone coating on the alloy in order to improve and modify the biological properties of this alloy. For this purpose, nano composite coating and polycaprolactone coating were first cr...
Show More
Research Article
Effect of Hybrid Nanofillers on the Mechanical Characteristics of Polymethyl Methacrylate Denture Base Composite
Issue:
Volume 8, Issue 2, December 2024
Pages:
30-43
Received:
29 August 2024
Accepted:
13 September 2024
Published:
26 September 2024
DOI:
10.11648/j.cm.20240802.12
Downloads:
Views:
Abstract: The research study focused on enhancing the mechanical characteristics of polymethyl methacrylate (PMMA) denture bases. PMMA is commonly used in dentistry due to its easy fabrication, cost-effectiveness, and favourable physical properties. However, its limitations include low wear resistance, hardness, and mechanical strength, making it less suitable for long-term dental applications. To address these limitations, the study employed a combination of hybrid nano-fillers, specifically HNTs (halloysite nanotubes) and MWCNTs (multi-walled carbon nanotubes), at varying loading levels to improve the mechanical characteristics of the PMMA composite. These nano-fillers underwent treatment by using a coupling agent to enhance their compatibility with PMMA. Key findings of the research include that introducing HNTs/MWCNTs into the PMMA matrix led to a substantial increase in flexural strength, with a significant improvement of 109.1 MPa compared to unfilled PMMA. This indicates that the composite material became more resistant to bending or deformation. There was a substantial rise in flexural modulus values, suggesting improved stiffness in the nanocomposite compared to unfilled PMMA. In addition, the tensile strength of the PMMA composite increased by 64.4 MPa with the addition of the hybrid nano-fillers, indicating enhanced resistance to stretching or pulling forces. The study found that the improvement in flexural and tensile strength was dependent on the concentration of MWCNTs. Increasing the MWCNT concentration up to 0.75 wt.% led to improved mechanical properties, but further increases resulted in a reduction in PMMA properties. Although there was a modest improvement in Vickers hardness (approximately 18.93 kg/mm2), the addition of HNTs/MWCNTs as hybrid nano-fillers effectively enhanced the properties of the PMMA nanocomposite. The study concludes that incorporating hybrid nano-fillers into PMMA could contribute to the longevity and durability of dental composites, addressing some of the material's inherent limitations. The specific combination and concentration of nano-fillers played a crucial role in determining the mechanical properties of the resulting nanocomposite.
Abstract: The research study focused on enhancing the mechanical characteristics of polymethyl methacrylate (PMMA) denture bases. PMMA is commonly used in dentistry due to its easy fabrication, cost-effectiveness, and favourable physical properties. However, its limitations include low wear resistance, hardness, and mechanical strength, making it less suitab...
Show More
,
Mahshid Sadeghi
